Supermoto & moped summer 2019 – Compilation

Damn, how many, damn. Are you recording too? Yes He over filled his tank and now he’s trying to spill some of it out. (Laughter) This is quality stuff right here (Kicked moped with leg) (laughter) Gas, gas, gas (Laughter) Did you see that last time I tried to wheelie? No, I dropped the plastic […]

Sascha auf LKW-Tour #116 (Von lauten Mopeds und Dauerbremslicht)

And now the new episode “Sascha on lorry tour” They are kept under wraps. And you believe because you haven’t turned your headlights on just make the exhaust pipe louder. We’ll hear you, we can’t see you but we’ll hear you. Because all of us drive by ear. I’m proud that you tailgate another car. […]

Alternative zum Simson Vogelserie Gasgriff?! – Lenkerblechhalter

9. Motorcycle Endorsement Requirement (for Florida). Pro Tip: Separate Your Keys, Parking on Campus

How to Add Gasoline/Petrol Fuel to Your Motorcycle

Hey how’s it going people BrownBrady here And thank you for tuning into my channel A friend of mine asked me to put together A video on how to add gas to a motorcycle And so this episode is all about that I’ll show you how to add gas or What our European cousins call […]

3. Gas Cap Location and How To Access Your Fuel Tank, Fuel Tips, Kill Switch.

– Next is the gas cap location. So, on this particular vehicle and a lot of vehicles, the seat opens with the ignition. So if I just put the key in right here and simply push in and turn to the left, my seat will pop open. You can see I got the helmet and […]

4. Low Idle Speed on Your Scooter

– One thing I like to remind people, it is 100 percent normal for scooters to kind of idle low when they first start up, when it’s nice and cool outside. It might idle low. It might sound like when you first start it up it’s gonna die. I’m very impatient. I don’t like to […]

How to make a mini Hydrogen Generator / TUTORIAL

您需要準備這些東西 2個同尺寸的冰棒棍 在棍面上畫上鑽孔點 再叧一根棍面上重做一次 再穩穩的將兩根冰棍壓緊 鑽孔 鑽孔後就像這樣 每相隔一個孔鎖上一個螺絲並穿過兩冰棍 再換面重做一次 再螺面上焊上錫點(可視螺絲材質選用合適的錫) 換面重做一次 然後 再螺面錫點上焊上電線 現在 可以將導電模組放入玻璃瓶中 瓶蓋上要鑽一個合適孔徑的洞 拿出西藥房買的滴管組 切掉上端 將電線穿過瓶蓋開孔 再將滴管組的觀察室塞進孔中,盡量塞緊 再用熱融膠封口,確保氣體不外洩 鎖緊瓶蓋 再依據實際需求剪截滴管 在集氣瓶鑽2個合適大小的孔 將滴管末端由孔1塞入瓶中 一定要將管子穿到瓶底 再將裁剩的那截滴管由孔2穿入瓶內.不必穿太深 再以熱融膠封口 這時 可以倒入清水了 蓋上瓶蓋 取一些鹽加水攪均 再打開瓶1 (導電模組) 倒入剛才自製的鹽水(導電液) 要淹滿整個導電模組 鎖緊瓶蓋 現在可以將電線接上電源供應器了 調整輸出電壓為 2.1 伏特 現在 您會看到瓶內開始有汽泡產生 (泡泡測試)

Your 2-Stroke Scooter Switches

– The headlight on this particular vehicle is always on but it has a little high beam switch right here. So, if I flip that little high beam switch on that’ll put the high beam. The switch is right here, as you can see. I’ll flip the high beam on. The blinkers are right here, […]

6. Your Scooter’s Battery Location, Where You Add 2-Stroke Oil.

– Now your battery location is actually located on most scooters, and on this one, right up here underneath the floorboard. So that’s where the battery is located. Batteries typically last one to one and a half years. Sometimes if you’re lucky, you’ll get two years out of ’em depending on how well you take […]